2D/3D controllerLJ-X8002

规格

Model

LJ-X8002

Head input

最多2个头部单位
Compatible with LJ-X8000 Series heads and LJ-V7000 Series heads
*使用2个单位时,头A和B是相同的模型。

采样周期(触发间隔)

[2D mode] Maximum speed of 1 kHz (1 ms)*1
[3D模式]连接LJ-X8000系列时:16 kHz的最大速度(63μs)*1
连接LJ-V7000系列时:64 kHz的最大速度(16μs)*2
(Luminance output types for model designations ending with B have a maximum speed of 8 kHz (125 μs))*3

注册检查设置数量

对于每个SD卡1和2,最多1000(取决于SD卡容量和设置内容),也可以进行外部切换

Master profile / number of reference images

[2D mode]Maximum 200 per setting per head (depends on SD card capacity)
[3D模式]每个设置最多400(取决于SD卡容量)

存储卡

•年代D card slot × 2
•年代upports OP-87133 (512 MB), CA-SD1G (1 GB), CA-SD4G (4 GB), CA-SD16G (16 GB)
*在SD1插槽中,CA-SD4G配备为8000,CA-SD1G配备为8000E标准

Number of tools

[2D mode]100/setting (of those, 20 are for misalignment correction)
[3D mode]Maximum of 100/setting

界面

Control input

20 points (input terminal block: 5 points, parallel I/O: 15 points)

Control output

28分(输出端子块:6分,并行I / O:22分)
照片MOSFET.*4

RS-232C

•值输出和控制I / O.(exclusive use with PLC link using an RS-232C port)
•年代upports baud rates up to 230,400 bps

PLC link

•使用以太网端口或RS-232C端口的值输出,并控制I / O.
(Exclusive use with Ethernet/IP™ and PROFINET. When using an RS-232C port, exclusive use with RS-232C no-procedure communication)

以太网

•值输出和控制I / O.
•除上述功能外,还可以上传/下载检查设置,执行各种模拟,发送/接收包括配置文件和图像数据的各种数据,并通过Keyence PC应用程序软件与远程连接程序一起使用
•支持FTP客户端和FTP服务器功能
•年代upports VNC server functions (for non-PC clients, only displaying the monitor screen is supported)
•支持BOOTP函数
•1000base-t / 100base-tx / 10base-t
•支持Jumbo帧(连接到CB-NEC20E / NEP20E / NPN20E中的任何一个时)

USB

•可以输出值(仅限3D模式),上传/下载检查设置,执行各种模拟,发送/接收包括配置文件和图像数据的各种数据,并通过Keyence PC应用软件与远程连接程序一起使用
•专用USB 2.0

以太网/ IP.TM值

•可以输入/输出数值并使用以太网端口或可选的以太网/ IP™单元CB-NEP20E执行控制I / O(不能与PLC Link,PROFINET和EtherCAT®)
•支持循环通信(最多1436个字节)和消息通信
• Maximum number of connections: 32 (Ethernet port)/1: Exclusive Owner, 4: Input Only (CB-NEP20E)
•符合版本.CT15(以太网端口)/ CT17(CB-NEP20E)一致性测试

PROFINET

• Can input/output numerical values and perform control I/O using the Ethernet port or the optional PROFINET unit CB-NPN20E (Cannot be used with PLC Link, EtherNet/IP™, and EtherCAT®)
•年代upports cyclic communication (max. 1408 bytes) (Ethernet port) / 1252 bytes (CB-NPN20E)
•支持非循环通信(记录数据)
•符合A(以太网端口)/ C(CB-NPN20E)的一致性A类(CB-NPN20E)

EtherCAT®

• Can output numerical values and perform control I/O by connecting the optional EtherCAT® unit CB-NEC20E (Cannot be used with PLC link, EtherNet/IP™, and PROFINET)
•支持循环通信(进程数据对象通信)(输入:最大536字节/输出:最大532字节)
•支持非循环通信(邮箱通信)
•年代upports CoE
•显式设备识别
•符合V2.2.10和V2.2.1.0一致性测试

老鼠

Various menus can be controlled via the dedicated mouse (included with the controller)

SNTP.

通过连接到SNTP服务器可以自动校正本机的日期和时间

USB HDD

通过将HDD(最大2 TB)连接到专用USB端口(支持USB 3.0,
总线供电,额定输出:900 mA),配置文件,图像和其他数据可以输出

监视输出

Analog RGB output, XGA 1024 × 768 (24-bit color, 60 Hz)

编码器输入

1 port: combination RS-422 line-driver output (with 5 V output: maximum 150 mA) open collector output (compatible with 5 V, 12 V, 24 V)

Response frequency

RS-422

Single phase / Z phase: 1.6 MHz, 2 phase / 1x: 1.6 MHz, 2 phase / 2x: 3.2 MHz, 2 phase / 4x: 6.4 MHz

开放收集器(OC)

Single phase / Z phase: 100 kHz, 2 phase / 1x: 100 kHz, 2 phase / 2x: 200 kHz, 2 phase / 4x: 400 kHz

Laser ON input

Non-voltage input (Shorted with short pin when shipped from factory)

冷风扇

假如

最小显示单元

[2D模式]0.1μm0.000004",0.01°,0.00001 mm2
[3D模式]0.1μm0.000004",0.001°,0.0001 mm2,0.00001 mm3.

语言

Switchable between English, Japanese, Simplified Chinese, Traditional Chinese, Korean, German, French, Italian, Thai, Czech, Hungarian, and Polish

Ratings

Power voltage

24 V DC ±10%

最大电流消耗

3..3 A

Environmental resistance

环境温度

0 to +45°C32到+ 113°F(DIN导轨安装)/ 0至+ 40°C32至+ 104°F(底表面安装)

相对湿度

3.5 to 85% RH (no condensation)

重量

约。2500 G.

*1When the measurement range is narrowed in accordance with the binning settings.
*2当测量范围设定为最小时,衬砌接通,并行成像已打开。所有其他设置都是默认值。
*3当分箱和并行成像都均开启时。所有其他设置都是默认值。
*4NPN输入设备支持正常共同,以及PNP输入设备的负常见连接。

其他型号