传感器主单元40A / 50A型FD-Q50C.

规格

模型

FD-Q50C.

支撑管直径

1 1/2“(40a),Ø44至Ø52(mm)
2“(50a),Ø52至Ø64(mm)

支持ed pipe materials

金属管/树脂管* 1

支持的流体

Various liquid [i.e. water (including DI), oils, chemicals, etc.]* 1

支持的液体温度

0到85°C32到185°F(管道表面上没有冻结)* 2

最大额定流量

1 1/2“(40 a):400升/分钟,105.7克/分钟
2“(50 a):500升/分钟,132.1克/分钟

零切流量

25 L / min(默认)* 3.

显示方法

状态指示灯,输出指示灯,带4位数,7个段LED,稳定级别指示器的双排显示

显示更新周期

约。3 Hz.

显示屏分辨率

0.1 / 1(默认:1)(L / min)

响应时间

0.5 S / 1.0 S / 2.5 S / 5 S / 10 S / 30 S / 60 S.

Protection circuit

电源反向连接,电源电源浪涌保护,
每个输出短路保护,每个输出电涌保护

重复性

0.5 s:±2.0%,1 s:±1.5%,2.5 s:±1.0%,5 s:±0.5%,10 s:±0.35%,30 s:±0.2%,60 s:±0.15%(/F.S.* 4.(Specific to selected response time))

滞后

Variable

Integrated flow unit display

1/10 / 100/1000 / 10000(默认:1)(L)

Integrated flow data storage cycle

每10秒保存到内存

内存备份

EEPROM (Data storage length: 10 years or longer, Data read/write frequency: 1 million times or more)

电源I / O连接器

M12 4针连接器

输入/输出(可选)

输出(CH.1 / CH.2)

控制输出/脉冲输出/错误输出(可选,默认值:CH.1控制输出/ CH.2未使用),
NPN / PNP设置可切换,开路收集器输出30 V或更低,最大。100 mA / Ch。,剩余电压2.5 V或更低* 5.

模拟输出(CH.1 / CH.2)

4至20 mA / 0至20 mA(可选,默认:未使用),负载电阻500Ω或更小* 5.

外部输入(CH.2)

集成流复位输入/流量零输入/原点调整输入(可选,默认:未使用),
短路电流1.5 mA或更低,输入时间20 ms或更多* 5.

电源

Power voltage

20至30 VDC,纹波(P-P)10%MAX,类/ LPS

Current consumption

130 mA或更少(负载电流排除)* 6.

Environmental resistance

外壳评级

IP65 / IP67(IEC60529)

环境温度

-10到+60°C14至140°F(没有冻结)

相对湿度

35至85%RH(无凝结)

Vibration resistance

10 to 55 Hz, Double amplitude 1.5 mm0.06“,在x,y和z方向中的每一个中2小时

抗冲击

100米/秒2, 16 ms pulse, 1,000 times in each of the X, Y, and Z directions

材料

传感器主机

PPS / PES / PBT / SU303 / SUS304 / SUSXM7

Sensor surface

橡皮

Mounting bracket

SUS304 / PA / POM / SUXM7

重量

约。640克(包括安装支架)

* 1液体必须允许通过超声波脉冲的通过,并且不含大的气囊或过度气泡。在某些非标准管(即衬里管道)上,检测可能不稳定
* 2日本基恩士当管的温度我联系s greater than 85°C185°F
* 3.The zero cut flow rate can be changed in the settings. When using the unit with a low flow rate range, perform an origin adjustment when the fluid is not moving if you change the zero cut flow rate.
* 4.当流速分布稳定时,该规范有效。该值不考虑由于设施因素导致的流速分布中的脉动或波动的影响。转换F.S.(全规模)根据额定流量范围在表中列出。
* 5.IO-Link: Compatible with Specification v1.1 / COM2 (38.4 kbps) The setting file can be downloaded from the KEYENCE website. If using the unit in the environment where downloading the file is not possible via internet, contact your nearest KEYENCE office. IO-Link is either registered trademarks or trademarks of PROFIBUS Nutzerorganisation e.V. (PNO)
* 6.When including the loads, please add 200 mA to this value.

其他型号