传感器放大器主单元IX-1000

模型

IX-1000

主单元/扩展单元

Main unit

Display

Min. display unit

10 µm^*1

Display range

±999.99 to ±999 mm (with 4 selectable steps)^*1

工具

Scan mode

Height, Height difference, Max./Min., Height difference calculation, Thickness calculation, Height detection, Monochromatic detection, Position adjustment
（最大设置数）检测：16个刀具，位置调整：1个刀具^*2

Line mode

Height (Ave./Max./Min.) , Height difference (Ave./Max./Min.) , Height difference calculation, Thickness calculation, Position adjustment, Tilt correction
（最大设置数）检测：16个刀具，位置调整：1个刀具，对齐调整：1个刀具^*2

Other functions

Common

零点/偏移、工作阈值调整、两点校准、测量方向、位置校正和测量，
Zero/offset recording,Capture mode (HDR) Sensor date/time Information addition, N.O./N.C. switching, I/O monitor,
Automatic brightness adjustment, Lighting (ON/OFF) , Total judgment conditions,NPN/PNP switching, Simultaneous main unit/expansion unit input, Light interference prevention, Security

Scan mode

测量范围、测量位置（小/标准/大）、测量模式、测量噪声消除、，
成像模式（高增益）、倾斜校正（固定或实时校正）、眩光消除、触发输入（内部/外部），
Trigger interval, Trigger delay, Trigger error, Monochrome histogram, Fixed reference area, Mask outline, Rotation range

Line mode

Average count, Laser position adjustment, Timing input, Head tilt correction (fixed only), Ambient light removal for measurement, HOLD function, Alarm setting, Measurement method (Ave./Max./Min.)

输入

输入

Non-voltage input/voltage input is switchable
For non-voltage input: ON voltage 2 V or lower, OFF current 0.1 mA or lower, ON current 2 mA (short circuit)
电压输入：最大输入额定值26.4 V，开启电压18 V或更高，关闭电流0.2 mA或更低，开启电流2 mA（24 V）

输入数

8（IN1到IN8）

作用

IN1：外部触发上/下定时，IN2至IN8：通过分配可选功能启用
Assignable functions: Program switching, Laser emission stop, Zero/offset (batch) , Reset (error only) , Reset (judgment value only) Reset (judgment value and error)

Output

Output

Open collector output; NPN/PNP switchable, N.O./N.C. switchable
对于开路集电极NPN输出：最大额定值为26.4 V，50 mA（连接到扩展单元时为20 mA），剩余电压为1.5 V或更低
For open collector PNP output: Maximum rating of 26.4 V, 50 mA (20 mA when linked to an expansion unit) , residual voltage of 2 V or less

输入数

10 (OUT1 to OUT10)

作用

Enable by assigning the optional functions
Assignable functions: Total judgment result (All OK, Any OK/NG) , run, busy, error, position adjustment result, tilt correction result,
Monochromatic detection/Height detection tool result (OK/NG) , Height/height difference/Max./Min./calculation tool result (OK/NG/HIGH/LO) , Alarm

Analog voltage output

±5 V, 1 to 5 V, 0 to 5 V, Output impedance: 100 Ω^*3

模拟电流输出

4至20 mA，最大负载电阻：350Ω^*3

项目数量

32

informa的统计tion

扫描模式：测量值/相似度（最大、最小、平均）、处理时间（最新、最大、最小、平均）、计数（OK数/NG数/触发器数）
行模式：测量值/相似度（最大值、最小值、平均值）、计数（OK数/NG数/触发器数）^*1*4

Detection history

Saved history

100^*5

Save conditions

Selectable from NG only / All^*5

Ethernet

Standard

100BASE-TX/10BASE-T^*6

Connector

RJ45 8针连接器^*6

Interface compatibility

CC-Link / DeviceNet^TM/以太网/IP^TM/以太猫^Ⓡ/RS-232C/BCD/PROFINET/PROFIBUS/TCP/IP输出^*7

可连接单元的数量

Main units: 1, Expansion units: 1, Communication units (DL) : 1

评级

电源电压

24 VDC±10%（包括纹波）

电流消耗

最大1.9 A或以下（仅主机组：0.8 A或以下，机组扩展：1.9 A或以下）（不包括输出负载）^*8

环境阻力

Ambient temperature

0至+50°C32至122华氏度(No freezing)

相对湿度

35 to 85 % RH (No condensation)

Material

Main unit case: PC/Power connector: PA, POM/Analog output connector: PA, POM/I/O connector: PA/
头部连接器：镀锌+镀镍，PA/以太网连接器：铜合金+镀镍/
Rear heat sink: Aluminum/Main unit rear DIN rail fixing tab: POM/Nameplate: PC

Weight

Approx. 210 g